Zoeken in normen
918 resultaten
I.2.1 Factor A: the age of the installation
The installation is:
A1
less than 10 years old.
Weighting: 0
A2
more than 10 years old.
Weighting: 5
A3
more than 20 years old.
Weighting: 8
A4
more than 30 years old.
Weighting: 10
I.2.3 Factor C: the environmental conditions
C1
The environment in which the installation is used:
a)
is clean and dry,
b)
contains no explosive or corrosive gases,
c)
presents no fire hazard as a result of dust, and
d)
is free of transport equipment or heavy equipment.
Weighting: 0
C2
The environment in which the installation is used:
a)
is not clean and dry or
b)
contains explosive or corrosive gases or
c)
presents a fire
I.3 Determining the time between two successive inspections
I.3.1 The time between two successive inspections is determined on the basis of the sum
of the factors A to E, using table I.1 in conjunction with
figure I.1.
Table I.1
—
Determining the sum of the factors A to E
Factor
Code
Weighting
Results
A
A1
0
A2
5
A3
8
A4
10
B
B1
0
B2
2
B3
4
B4
7
B5
15
C
C1
0
C2
10
C3
20
D
D1
J.4.3
The batch size is the collection of products assembled in the same way from which
the random sample shall be taken and inspected to determine whether the approval criteria
are complied with.
J.4.6
The random sampling units shall be chosen at random from the batch, without regard
to quality.
K.1 The time between two successive inspections
The time between two successive inspections of electrical work equipment shall be
determined by:
A) the frequency of use;
B) the expertise of the users;
C) the environment;
D) the chance of damage.
K.3 Determining the time between two successive inspections
K.3.1 The time between two successive inspections is determined on the basis of the sum
of the factors A to D, using
table K.1 in conjunction with
figure K.1.
Table K.1
—
Determining the sum of the factors A to D
Factor
Code
Weighting
Results
A
A1
10
A2
0
B
B1
0
B2
10
C
C1
0
C2
10
C3
15
D
D1
0
D2
10
D3
15
Total
K.3.2 Read out the
K.3.2
Read out the time between two successive inspections from
figure K.1.
Figure K.1
—
The time between two successive inspections
L.2
The actual earth leakage current can also be measured by measuring the differential
current in the live parts of the connection.
L.4
Due to the difficulty of measuring the actual earth leakage current, the replacement
earth leakage current is often measured. The live parts are interconnected here. An
alternating voltage is applied between the live parts on the one hand and the protective
conductor or the exterior conducting parts of the item of electrical work equipment
on the other. The current measured is the replacement earth
Zoeken in de website
52 resultaten
NEN 3140+A2:2018 geeft een andere visie op het inspectiebeleid
We werken alweer drie maanden met NEN 3140+A2:2018. Dit artikel gaat over de gewijzigde benadering van de inspecties van bestaande elektrische installaties. Dit kan een reden zijn voor de installatieverantwoordelijke (IV) zijn inspectiebeleid te herzien.
In 5.3.3.1.101 van NEN 3140+A1: 2015 staat een bepaling die stevig in het gedachtengoed van elektrotechnisch Nederland is verankerd: “Bij inspectie
Inspectiefrequentie installaties
Artikel 5.101 uit NEN 3140 geeft de eisen weer van een inspectie van bestaande elektrische installaties. De tijd tussen twee opeenvolgende inspecties moet voldoen aan bijlage I. Met deze rekentool kunt u bepalen hoeveel tijd er tussen inspecties mag zitten. Een afzonderlijk tijdsinterval kan worden vastgesteld voor elke elektrische installatie en voor elk onderdeel van een elektrische installatie.
Rekentools
Deze rekentools helpen u om vast te stellen:
Inspectie- en instructietermijnen
Met Bijlage E kunt u vaststellen wanneer een VOP, VP, WV of IV opnieuw instructie moet krijgen.
Bijlage I geeft de termijn aan voor inspectie van uw elektrische installaties.
Bijlage K geeft de termijn aan voor inspectie van uw elektrische arbeidsmiddelen.
Steekproefbepaling
Met bijlage J kunt u de grootte
Bestaat er een NEN 3140-keuringssticker?
Nee, die bestaat niet. De eis die in de norm wordt gesteld, is dat elektrische arbeidsmiddelen aantoonbaar moeten zijn goedgekeurd voor het gebruik (bepaling 5.102.84 in de norm). De wijze waarop dit aantoonbaar wordt gemaakt, is niet voorgeschreven.
Moet bij het plaatsen van een cv-ketel worden voldaan aan NEN 3140? In het bijzonder op het onderdeel brandwerende doorvoeren en gasbelemmering.
NEN 3140 richt zich op het veilig werken aan en met elektrische installaties en arbeidsmiddelen. Voor oplevering van nieuwe elektrische installaties en arbeidsmiddelen zijn veel uitgebreidere inspecties noodzakelijk. Niet alleen moet dan naar de veiligheidsaspecten worden gekeken, maar ook moet worden gekeken of de functionele eisen goed zijn ingevuld.
Brandwerende doorvoeren en gasbelemmering behoren
NEN heeft een training voor Vakbekwaam Persoon. Wat zijn de leerdoelen van de cursus?
U leert op hoofdlijnen wat de Arbowet vraagt en wat het Arbobesluit aangeeft. Verder wordt u bekend met de inhoud van de norm NEN 3140. Je leert risico’s en gevaren herkennen (waaronder aanrakingsgevaar en de vlamboog) en je leert in de training wat de positie is van de Vakbekwaam Persoon ten opzichte van andere aanwijzingsniveaus binnen een organisatie. Tot slot leer je hoe je veilig werkt aan een