Zoeken in normen
918 resultaten
E.2.4 Factor D: the working conditions
The working conditions:
D1
completely dead.
Weighting: 0
D2
regularly in the vicinity of live parts.
Weighting: 5
D3
from time to time live working.
Weighting: 10
E.2.7 Factor G: the level of change in the work activities
The level of change in the work activities:
G1
little.
Weighting: 5
G2
regularly.
Weighting: 0
E.3 Determining the time between two successive periods of instruction
E.3.1 The time between two successive periods of instruction is determined on the basis
of the sum of the factors A to H, using
table E.1 in conjunction with
figure E.1.
Table E.1
—
Determining the sum of the factors A to H
Factor
Code
Weighting
Results
A
A1
0
A2
10
B
B1
0
B2
5
B3
10
C
C1
5
C2
0
C3
5
D
D1
0
D2
5
D3
10
E
E.3.2
Read out the time between two successive periods of instruction from
figure E.1.
Figure E.1
—
The time between two successive periods of instruction
F.2 Responsibilities of the person responsible for an electrical installation
The person responsible for an electrical installation is responsible for:
— electrical installations and electrical work equipment;
— maintaining the safety of electrical installations and electrical work equipment by
regular inspections and timely repair of any defects found;
— setting up an access scheme for premises with an electrical hazard;
— establishing procedures
F.4 Responsibility in the event of dead working
F.4.1 Making a part of an installation dead is the responsibility of the person responsible
for an electrical installation. This does not mean that the person responsible for
an electrical installation shall make the installation dead in person.
F.4.2 The nominated person in control of a work activity is responsible for safety at the
work location.
F.4.3 The responsibility of
F.4.1
Making a part of an installation dead is the responsibility of the person responsible
for an electrical installation. This does not mean that the person responsible for
an electrical installation shall make the installation dead in person.
G.1 Use situations
Table G.1 states the most common use situations for the individual items of protective equipment
and for other equipment and devices.
Table G.1
—
Use of protective or other equipment and devices
Protective or other equipment or device
Applicable standard
Examples of use situations
a When choosing the protective equipment against arc hazard, consider the arc energy
that can occur
H.1
The risk associated with carrying out electrical measurements depends on:
— the measurement instrument;
— the situation in which the measurements are carried out;
— the way in which the measurements are taken.
H.7
If measuring in accordance with
H.6 is not possible, the rules that apply to live working (see
6.3) should be applied.
Zoeken in de website
52 resultaten
NEN 3140+A2:2018 geeft een andere visie op het inspectiebeleid
We werken alweer drie maanden met NEN 3140+A2:2018. Dit artikel gaat over de gewijzigde benadering van de inspecties van bestaande elektrische installaties. Dit kan een reden zijn voor de installatieverantwoordelijke (IV) zijn inspectiebeleid te herzien.
In 5.3.3.1.101 van NEN 3140+A1: 2015 staat een bepaling die stevig in het gedachtengoed van elektrotechnisch Nederland is verankerd: “Bij inspectie
Inspectiefrequentie installaties
Artikel 5.101 uit NEN 3140 geeft de eisen weer van een inspectie van bestaande elektrische installaties. De tijd tussen twee opeenvolgende inspecties moet voldoen aan bijlage I. Met deze rekentool kunt u bepalen hoeveel tijd er tussen inspecties mag zitten. Een afzonderlijk tijdsinterval kan worden vastgesteld voor elke elektrische installatie en voor elk onderdeel van een elektrische installatie.
Rekentools
Deze rekentools helpen u om vast te stellen:
Inspectie- en instructietermijnen
Met Bijlage E kunt u vaststellen wanneer een VOP, VP, WV of IV opnieuw instructie moet krijgen.
Bijlage I geeft de termijn aan voor inspectie van uw elektrische installaties.
Bijlage K geeft de termijn aan voor inspectie van uw elektrische arbeidsmiddelen.
Steekproefbepaling
Met bijlage J kunt u de grootte
Bestaat er een NEN 3140-keuringssticker?
Nee, die bestaat niet. De eis die in de norm wordt gesteld, is dat elektrische arbeidsmiddelen aantoonbaar moeten zijn goedgekeurd voor het gebruik (bepaling 5.102.84 in de norm). De wijze waarop dit aantoonbaar wordt gemaakt, is niet voorgeschreven.
Moet bij het plaatsen van een cv-ketel worden voldaan aan NEN 3140? In het bijzonder op het onderdeel brandwerende doorvoeren en gasbelemmering.
NEN 3140 richt zich op het veilig werken aan en met elektrische installaties en arbeidsmiddelen. Voor oplevering van nieuwe elektrische installaties en arbeidsmiddelen zijn veel uitgebreidere inspecties noodzakelijk. Niet alleen moet dan naar de veiligheidsaspecten worden gekeken, maar ook moet worden gekeken of de functionele eisen goed zijn ingevuld.
Brandwerende doorvoeren en gasbelemmering behoren
NEN heeft een training voor Vakbekwaam Persoon. Wat zijn de leerdoelen van de cursus?
U leert op hoofdlijnen wat de Arbowet vraagt en wat het Arbobesluit aangeeft. Verder wordt u bekend met de inhoud van de norm NEN 3140. Je leert risico’s en gevaren herkennen (waaronder aanrakingsgevaar en de vlamboog) en je leert in de training wat de positie is van de Vakbekwaam Persoon ten opzichte van andere aanwijzingsniveaus binnen een organisatie. Tot slot leer je hoe je veilig werkt aan een