Zoeken in normen
918 resultaten
6.3.102 Interruption
A short interruption, where the work location is not left, is not regarded as an interruption.
6.4.1.5
The work location should be marked out by suitable barriers, ropes, flags, lamps,
signs etc.
Adjacent live switch panels shall be distinguished by additional, clearly visible
means, for example clear warning signs secured to the front of doors.
6.4.2.1
These protective devices shall be selected and installed to provide sufficient protection
against the expected electrical and mechanical stresses.
6.4.2.1.101 The provisions used as screens, barriers, insulating or other covers shall be properly
maintained and stay in place during the work activities.
6.4.2.1.102 When installing such protective devices in the live working zone, this
6.4.2.1.102
When installing such protective devices in the live working zone, this shall be done
according to the procedure for dead working or according to the procedure for live
working.
6.4.4 Construction work and other non-electrical work
[not applicable]
6.101.2
Work activities in other risk-increasing conditions
NOTE See also
annex N.
6.101.2.1 Risk-increasing conditions can be present in installations, premises and environments.
Work activities with risk-increasing conditions shall require extra safety measures
to be taken, depending on the level of the risk, the nature of the work activities,
the use and the condition of the installation
6.101.2.1
Risk-increasing conditions can be present in installations, premises and environments.
Work activities with risk-increasing conditions shall require extra safety measures
to be taken, depending on the level of the risk, the nature of the work activities,
the use and the condition of the installation and the current conditions.
6.101.2.2
If regularly recurring work activities are involved, these extra safety measures shall
be established in writing.
NOTE 1 The other risk-increasing conditions relate to:
a) premises with damp, such as:
1) premises with a bath, shower, swimming pool or sauna;
2) marinas;
3) business premises and sites for agriculture, horticulture and stock farming;
4) cable pits
7 Maintenance procedures
7.1 General
7.1.1 The purpose of maintenance, is to keep the electrical installation in the required
condition.
Maintenance may consist of:
— preventive maintenance:which is carried out on a routine basis with the intention of preventing breakdown
and keeping equipment in good condition;
— corrective maintenance:which is carried out to repair or replace a defective part.
7.1.2
There are two types of maintenance work:
— work where the risk of electric shocks, short-circuit or arcing is present and therefore
the appropriate working procedures (see
Clause 6) have to be applied;
— work where the design of equipment enables certain maintenance (for example replacement
of fuses or light bulbs) to be undertaken safely without full working procedures as
described
Zoeken in de website
52 resultaten
NEN 3140+A2:2018 geeft een andere visie op het inspectiebeleid
We werken alweer drie maanden met NEN 3140+A2:2018. Dit artikel gaat over de gewijzigde benadering van de inspecties van bestaande elektrische installaties. Dit kan een reden zijn voor de installatieverantwoordelijke (IV) zijn inspectiebeleid te herzien.
In 5.3.3.1.101 van NEN 3140+A1: 2015 staat een bepaling die stevig in het gedachtengoed van elektrotechnisch Nederland is verankerd: “Bij inspectie
Inspectiefrequentie installaties
Artikel 5.101 uit NEN 3140 geeft de eisen weer van een inspectie van bestaande elektrische installaties. De tijd tussen twee opeenvolgende inspecties moet voldoen aan bijlage I. Met deze rekentool kunt u bepalen hoeveel tijd er tussen inspecties mag zitten. Een afzonderlijk tijdsinterval kan worden vastgesteld voor elke elektrische installatie en voor elk onderdeel van een elektrische installatie.
Rekentools
Deze rekentools helpen u om vast te stellen:
Inspectie- en instructietermijnen
Met Bijlage E kunt u vaststellen wanneer een VOP, VP, WV of IV opnieuw instructie moet krijgen.
Bijlage I geeft de termijn aan voor inspectie van uw elektrische installaties.
Bijlage K geeft de termijn aan voor inspectie van uw elektrische arbeidsmiddelen.
Steekproefbepaling
Met bijlage J kunt u de grootte
Bestaat er een NEN 3140-keuringssticker?
Nee, die bestaat niet. De eis die in de norm wordt gesteld, is dat elektrische arbeidsmiddelen aantoonbaar moeten zijn goedgekeurd voor het gebruik (bepaling 5.102.84 in de norm). De wijze waarop dit aantoonbaar wordt gemaakt, is niet voorgeschreven.
Moet bij het plaatsen van een cv-ketel worden voldaan aan NEN 3140? In het bijzonder op het onderdeel brandwerende doorvoeren en gasbelemmering.
NEN 3140 richt zich op het veilig werken aan en met elektrische installaties en arbeidsmiddelen. Voor oplevering van nieuwe elektrische installaties en arbeidsmiddelen zijn veel uitgebreidere inspecties noodzakelijk. Niet alleen moet dan naar de veiligheidsaspecten worden gekeken, maar ook moet worden gekeken of de functionele eisen goed zijn ingevuld.
Brandwerende doorvoeren en gasbelemmering behoren
NEN heeft een training voor Vakbekwaam Persoon. Wat zijn de leerdoelen van de cursus?
U leert op hoofdlijnen wat de Arbowet vraagt en wat het Arbobesluit aangeeft. Verder wordt u bekend met de inhoud van de norm NEN 3140. Je leert risico’s en gevaren herkennen (waaronder aanrakingsgevaar en de vlamboog) en je leert in de training wat de positie is van de Vakbekwaam Persoon ten opzichte van andere aanwijzingsniveaus binnen een organisatie. Tot slot leer je hoe je veilig werkt aan een