Zoeken in normen
918 resultaten
5.102.6
The person responsible for an electrical installation shall determine and record with
justification:
— the inspections to be carried out,
— the time between two successive inspections,
— the representative random sample,
— the measurement methods that are to be used and
— any measurement instruments that are to be used.
The regulations of the electrical work
5.102.7
Samples are only allowed if:
— low-risk electrical work equipment is concerned that is used under the same conditions
and
— the sum of the weighting factors in
annex K for this electrical work equipment is less than 16.
5.102.8
Electrical work equipment shall be demonstrably approved for use.
NOTE This can be demonstrated by means of a register stating the date of inspection, the
date of the next inspection, the inspection method and the approval. A sticker with
the next inspection date may also be applied to the electrical work equipment.
5.102.9
When inspecting electrical work equipment, it shall be checked whether the requirements
are met relating to:
a) the protection measures against:
— electrical shock;
— thermal effects;
— overcurrent;
— voltage failure;
b) the correct operation of the safety systems;
c) the correct use in view of the environmental conditions.
5.102.14
If the requirement of the insulation resistance cannot be complied with for electrical
work equipment of class I with heating elements, the actual leakage current may be
measured. The leakage current measured must not exceed the value of
table 103.
Table 103
—
Maximum values of the leakage current for class I electrical work equipment with heating
elements
Power
kW
Actual leakage
5.102.16
The resistance R of the protective conductor in connecting cables, extension cords and reels, including
the contact resistances, shall comply with:
where:
R
is the resistance of the protective conductor, including the contact resistances,
in Ω;
ρ
is the specific resistance of the conductor material, in Ω.mm2/m;
l
is the length of the protective conductor, in m;
S
is
6.1.0.101
The person who carries out the work activities shall be nominated for this. Any person
who has not been nominated for carrying out the work activities shall be under the
supervision of a person nominated for this purpose.
If the nominated person in control of a work activity does not actually manage the
work, this task may be delegated to a skilled person. This shall preferably be set
down in
6.2.3.101
The dead state may only be established using double-pole voltage indicators that comply
with or are equivalent to
NEN-EN-IEC 61243-3. The voltage indicators shall be checked for proper operation directly before and
after use.
6.3.0.104
Work in the live working zones of installations with in-line cartridge fuses of 100 A
to 630 A or automatic fuses of 25 A to 80 A requires the use of personal protective
equipment and a face mask.
NOTE The difference between the value of the cartridge fuse and the value of the automatic
fuse is caused by the amount of energy (I2t) transmitted in case of a short-circuit.
6.3.0.105
Safe working in the live working zones of installations with in-line cartridge fuses
of more than 630 A or automatic fuses of more than 80 A is not permitted because of
the arc hazard, unless the possible energy released has been calculated and the personal
protective equipment has been adapted for this.
NOTE The difference between the value of the cartridge fuse and the value of the automatic
Zoeken in de website
52 resultaten
Zijn procedures en schriftelijke werkinstructies echt nodig?
Grotere organisaties hebben vaak een technische dienst met geschoolde vakmensen die onderhoud, uitbreidingen en mutaties verrichten aan de elektrische installaties. NEN 3140 geeft aan dat elektrotechnici schriftelijk moeten worden aangewezen als vakbekwaam persoon (VP). In deze aanwijzing worden zij door of namens de werkgever bevoegd verklaard tot het uitvoeren van elektrotechnische werkzaamheden
Inspectiefrequentie arbeidsmiddelen
Elektrische arbeidsmiddelen moeten met een passende regelmaat worden geïnspecteerd.
De tijd tussen twee opeenvolgende inspecties is afhankelijk van:
de frequentie van het gebruik;
de deskundigheid van de gebruiker;
de omgeving;
de kans op beschadiging.
De tijd tussen twee opeenvolgende inspecties moet voldoen aan bijlage K. Deze rekentool helpt u de inspectietermijn te berekenen
Installaties: steekproefbepaling
Steekproefbepaling
Met bijlage J kunt u de grootte van de steekproef bepaling bij inspecties van grote aantallen arbeidsmiddelen of installaties.
De inspecties mogen worden uitgevoerd door middel van een representatieve steekproef volgens een statistisch verantwoorde methode.
Steekproef voor omvangrijke machines
De installatieverantwoordelijke bepaalt of er een steekproef gehouden wordt. In bijlage
Opleiding en ervaring NEN 3140
Informatie uit training NEN 3140 Installatie- werkverantwoordelijke.
Voordat een persoon kan worden aanwezen worden de volgende criteria voor een VP, IV en WV getoetst.
Heeft de aan te wijzen persoon voldoende ervaring met elektrotechnische werkzaamheden?
Heeft de als IV aan te wijzen persoon voldoende inzicht in de installatie, waarvoor hij zal worden aangewezen?
Heeft de als werkverantwoordelijke
NEN 3140 Bijlage E
AnnexInformativeDetermining time between two successive instructions
Table E.1 — Determining instruction frequency
Factor
Rating
Weighting
NPEI
NPWA
SP
Basisinformatie elektrotechniek: een goede voorbereiding op de Stipel-basistoets
In 1999 vroeg mijn toenmalige leidinggevende of ik een vergadering wilde bijwonen van Stipel. Ik kreeg een korte uitleg en ben aangeschoven. Ik weet nog dat veel langs mij heen ging, omdat ik er natuurlijk zomaar inviel. Stipel bestond toen nog niet zo lang en moest nog bekendheid krijgen in de markt.
Wat is Stipel?
Stipel staat voor: Stichting Persoonscertificatie Energietechniek.
Ik ben de enige werknemer van het bedrijf. Kan ik mijzelf aanwijzen?
Het is mogelijk om uzelf aan te wijzen mits u dat helder vastlegt.
In bijlage D van NEN 3140 staat wat in elk geval in het aanwijzingsdocument moeten worden opgenomen.
Waar vind ik de wettelijke eisen voor het keuren van elektrische arbeidsmiddelen volgens NEN 3140?
Het keuren van elektrische arbeidsmiddelen volgens NEN 3140 is gebaseerd op de Nederlandse arbowetgeving. Deze is te vinden op de website van de Nederlandse overheid: www.overheid.nl (zoekterm: Arbeidsomstandighedenwet).
Wanneer mag ik mijzelf een installatieverantwoordelijke (IV) of werkverantwoordelijke (WV) noemen?
Bij de rol van IV of WV horen de volgende taken en verantwoordelijkheden:
Een IV/WV beschikt over voldoende vakkennis (verkregen door opleiding en/of ervaring).
Een IV/WV heeft kennis en kunde van de betreffende elektrische installaties en arbeidsmiddelen in de omstandigheden waarin deze worden gebruikt (bedrijfsvoeringsomstandigheden, deze zijn bedrijfsspecifiek).
Een IV/WV beschikt