Zoeken in normen
918 resultaten
5.3.3 Inspection
5.3.3.1 The purpose of inspection is to verify that an electrical installation is in accordance
with safety regulations and the specified technical requirements of the relevant standards;
the inspection may include verification of the normal state of that installation.
New electrical installations as well as modifications and extensions of existing installations
shall be inspected prior to
5.3.3.3
Inspections shall be carried out with reference to relevant electrical drawings and
specifications.
5.3.3.3.101 In special cases, the person responsible for an electrical installation may decide
that the inspections can be carried out without drawings and specifications, for example
in simple and clearly arranged installations.
5.3.3.5.102
Inspections shall be carried out using suitable tools, equipment and devices and protective
equipment that prevent hazards, duly considering the hazards of uninsulated live parts.
5.101.6.1
When visually inspecting an installation it is checked whether:
a) the necessary drawings are present and the correct information is indicated;
b) the different (installation) parts are clearly identifiable;
c) any damage present does not cause a hazard;
d) the electrical equipment at least corresponds to the installation requirements;
e) the gangways intended for
5.101.6.2
When inspecting an installation by measuring and testing, it shall be checked that
the requirements have been met as regards:
a) the protective conductors and their connections;
b) the circuit impedances of the electrical system;
c) the earth distribution resistance of earth electrodes;
d) the insulation resistance of each section of the installation;
e) the safe
5.101.6.3
The following criteria shall apply to measurement and testing according to
5.101.6.2:
a) The uninterrupted state of the protective conductors and their connections shall be
measured with:
1) a measurement of the phase-earth circuit impedance or
2) a measurement of all the separate protective conductors with a measurement current
greater than or equal to 0.2 A.
b)
5.101.6.5
The earth distribution resistance of earth electrodes shall be measured using an alternating
voltage.
NOTE If the measurement is not reliable in urban areas, measuring the circuit impedances
will suffice.
5.101.6.8
It shall be established through measuring that the response current and time of earth
leakage circuit breakers do not exceed the values assigned. The proper operation of
the test button may only be checked after the measurements.
5.102.1 General
The electrical installations of extensive, complex and sizeable work equipment shall
be inspected according to
5.101.
Safety functions, such as emergency shutdown switches and collision protection devices
of such extensive, complex and sizeable work equipment shall be checked at least once
a year.
5.102.2
Electrical work equipment shall be inspected with suitable regularity.The time between two successive inspections depends on:
a) the frequency of use;
b) the expertise of the user;
c) the environment;
d) the risk of damage.
NOTE The purpose of regular inspections is to detect any defects that have occurred during
use and that pose a hazard.
Zoeken in de website
52 resultaten
Zijn procedures en schriftelijke werkinstructies echt nodig?
Grotere organisaties hebben vaak een technische dienst met geschoolde vakmensen die onderhoud, uitbreidingen en mutaties verrichten aan de elektrische installaties. NEN 3140 geeft aan dat elektrotechnici schriftelijk moeten worden aangewezen als vakbekwaam persoon (VP). In deze aanwijzing worden zij door of namens de werkgever bevoegd verklaard tot het uitvoeren van elektrotechnische werkzaamheden
Inspectiefrequentie arbeidsmiddelen
Elektrische arbeidsmiddelen moeten met een passende regelmaat worden geïnspecteerd.
De tijd tussen twee opeenvolgende inspecties is afhankelijk van:
de frequentie van het gebruik;
de deskundigheid van de gebruiker;
de omgeving;
de kans op beschadiging.
De tijd tussen twee opeenvolgende inspecties moet voldoen aan bijlage K. Deze rekentool helpt u de inspectietermijn te berekenen
Installaties: steekproefbepaling
Steekproefbepaling
Met bijlage J kunt u de grootte van de steekproef bepaling bij inspecties van grote aantallen arbeidsmiddelen of installaties.
De inspecties mogen worden uitgevoerd door middel van een representatieve steekproef volgens een statistisch verantwoorde methode.
Steekproef voor omvangrijke machines
De installatieverantwoordelijke bepaalt of er een steekproef gehouden wordt. In bijlage
Opleiding en ervaring NEN 3140
Informatie uit training NEN 3140 Installatie- werkverantwoordelijke.
Voordat een persoon kan worden aanwezen worden de volgende criteria voor een VP, IV en WV getoetst.
Heeft de aan te wijzen persoon voldoende ervaring met elektrotechnische werkzaamheden?
Heeft de als IV aan te wijzen persoon voldoende inzicht in de installatie, waarvoor hij zal worden aangewezen?
Heeft de als werkverantwoordelijke
NEN 3140 Bijlage E
AnnexInformativeDetermining time between two successive instructions
Table E.1 — Determining instruction frequency
Factor
Rating
Weighting
NPEI
NPWA
SP
Basisinformatie elektrotechniek: een goede voorbereiding op de Stipel-basistoets
In 1999 vroeg mijn toenmalige leidinggevende of ik een vergadering wilde bijwonen van Stipel. Ik kreeg een korte uitleg en ben aangeschoven. Ik weet nog dat veel langs mij heen ging, omdat ik er natuurlijk zomaar inviel. Stipel bestond toen nog niet zo lang en moest nog bekendheid krijgen in de markt.
Wat is Stipel?
Stipel staat voor: Stichting Persoonscertificatie Energietechniek.
Ik ben de enige werknemer van het bedrijf. Kan ik mijzelf aanwijzen?
Het is mogelijk om uzelf aan te wijzen mits u dat helder vastlegt.
In bijlage D van NEN 3140 staat wat in elk geval in het aanwijzingsdocument moeten worden opgenomen.
Waar vind ik de wettelijke eisen voor het keuren van elektrische arbeidsmiddelen volgens NEN 3140?
Het keuren van elektrische arbeidsmiddelen volgens NEN 3140 is gebaseerd op de Nederlandse arbowetgeving. Deze is te vinden op de website van de Nederlandse overheid: www.overheid.nl (zoekterm: Arbeidsomstandighedenwet).
Wanneer mag ik mijzelf een installatieverantwoordelijke (IV) of werkverantwoordelijke (WV) noemen?
Bij de rol van IV of WV horen de volgende taken en verantwoordelijkheden:
Een IV/WV beschikt over voldoende vakkennis (verkregen door opleiding en/of ervaring).
Een IV/WV heeft kennis en kunde van de betreffende elektrische installaties en arbeidsmiddelen in de omstandigheden waarin deze worden gebruikt (bedrijfsvoeringsomstandigheden, deze zijn bedrijfsspecifiek).
Een IV/WV beschikt