Zoeken in normen
918 resultaten
5.102.6
The person responsible for an electrical installation shall determine and record with
justification:
— the inspections to be carried out,
— the time between two successive inspections,
— the representative random sample,
— the measurement methods that are to be used and
— any measurement instruments that are to be used.
The regulations of the electrical work
5.102.7
Samples are only allowed if:
— low-risk electrical work equipment is concerned that is used under the same conditions
and
— the sum of the weighting factors in
annex K for this electrical work equipment is less than 16.
5.102.8
Electrical work equipment shall be demonstrably approved for use.
NOTE This can be demonstrated by means of a register stating the date of inspection, the
date of the next inspection, the inspection method and the approval. A sticker with
the next inspection date may also be applied to the electrical work equipment.
5.102.9
When inspecting electrical work equipment, it shall be checked whether the requirements
are met relating to:
a) the protection measures against:
— electrical shock;
— thermal effects;
— overcurrent;
— voltage failure;
b) the correct operation of the safety systems;
c) the correct use in view of the environmental conditions.
5.102.14
If the requirement of the insulation resistance cannot be complied with for electrical
work equipment of class I with heating elements, the actual leakage current may be
measured. The leakage current measured must not exceed the value of
table 103.
Table 103
—
Maximum values of the leakage current for class I electrical work equipment with heating
elements
Power
kW
Actual leakage
5.102.16
The resistance R of the protective conductor in connecting cables, extension cords and reels, including
the contact resistances, shall comply with:
where:
R
is the resistance of the protective conductor, including the contact resistances,
in Ω;
ρ
is the specific resistance of the conductor material, in Ω.mm2/m;
l
is the length of the protective conductor, in m;
S
is
6.1.0.101
The person who carries out the work activities shall be nominated for this. Any person
who has not been nominated for carrying out the work activities shall be under the
supervision of a person nominated for this purpose.
If the nominated person in control of a work activity does not actually manage the
work, this task may be delegated to a skilled person. This shall preferably be set
down in
6.2.3.101
The dead state may only be established using double-pole voltage indicators that comply
with or are equivalent to
NEN-EN-IEC 61243-3. The voltage indicators shall be checked for proper operation directly before and
after use.
6.3.0.104
Work in the live working zones of installations with in-line cartridge fuses of 100 A
to 630 A or automatic fuses of 25 A to 80 A requires the use of personal protective
equipment and a face mask.
NOTE The difference between the value of the cartridge fuse and the value of the automatic
fuse is caused by the amount of energy (I2t) transmitted in case of a short-circuit.
6.3.0.105
Safe working in the live working zones of installations with in-line cartridge fuses
of more than 630 A or automatic fuses of more than 80 A is not permitted because of
the arc hazard, unless the possible energy released has been calculated and the personal
protective equipment has been adapted for this.
NOTE The difference between the value of the cartridge fuse and the value of the automatic
Zoeken in de website
52 resultaten
Toelichting n-bepalingen / National Provisions from NEN1010:2015 (english).
Contents
Overview of the National provisions (n-provisions) from NEN 1010:2015
Reasons for the setup of the n-provisions list
Working with non-Dutch Parties
Differences
Examples
Application at Work
Target group for n-provisions
For more information
Overview
NEN 1010 is the most important standard in the field of electrical engineering in
Checklist: executiegevaar
Situatie
Tijdens werkzaamheden is een onder spanning staande kabel met bloot koper in aanraking gekomen met de kabelgoot. Dit heeft geleid tot een onder spanning staande kabelgoot. Een van de werknemers kreeg een elektrische schok van zijn ene naar zijn andere arm.
Risico's
Het risico’s met betrekking tot deze gebeurtenis:
Dit kan leiden tot een hartstilstand, bewusteloosheid, stoppen van
Training voor IV’ers en WV’ers
tekst: Aribert Guiking
foto's: Rob Kaspers
Rob Kaspers geeft trainingen aan installatieverantwoordelijken (IV) en werkverantwoordelijken (WV). Volgens hem zijn deze technici vaak 'bescheiden personen' en zijn ze niet gewend om af en toe stevig te onderhandelen om hun werk optimaal te kunnen doen. Via een tweedaagse training probeert hij dat te veranderen.
Rob Kaspers: “Je moet jezelf zichtbaar
Mag ik de norm uitprinten?
Dat mag, alleen is dit wel voor eigen gebruik.
Moet een NEN 3140-testapparaat zelf ook worden getest volgens NEN 3140?
NEN 3140 is gericht op het voldoen aan de Nederlandse arbowetgeving in het kader van elektrische veiligheid. Dat betekent dat de werkgever op de best mogelijke wijze zeker moet stellen dat het elektrische arbeidsmiddel waarmee hij zijn werknemer laat werken, elektrisch veilig is voor de gebruikelijke werkomstandigheden in de desbetreffende branche.
Een NEN 3140-toetsing zegt niets over de functionaliteit
Mogen wij bij renovatie van bestaande huurwoningen met de onderhoudsdienst van onze woningcorporatie complete keukens plaatsen en nieuw wandtegelwerk en waterleidingen aanbrengen of zijn wij verplicht deze werkzaamheden uit te besteden aan een erkend inst
Nederland kent geen verplichting (zoals wetgeving) om elektrotechnische werkzaamheden (of daarmee verband houdende werkzaamheden) door een elektrisch installatiebedrijf of erkend elektrisch installatiebedrijf te laten uitvoeren. Wel moeten elektrische werkzaamheden waaraan enig risico is verbonden, worden uitgevoerd door ter zake kundige en voldoende opgeleide en/of geïnstrueerde mensen (arbowetgeving
Op welke elektrische apparatuur is NEN 3140 van toepassing?
NEN 3140 is van toepassing op zowel elektrische installaties van gebouwen (en grote machines/industriële installaties) als elektrische arbeidsmiddelen.
Wat zijn de belangrijkste voorschriften uit NEN 3140?
Voor het bedrijfsleven in het algemeen zijn dat de voorschriften voor de periodieke elektrotechnische inspectie van elektrische installaties en de hierop aangesloten elektrische machines en arbeidsmiddelen (elektrische apparaten en gereedschappen).
Voor de specifieke elektrotechnische bedrijven zijn dat de voorschriften hoe zij veilig aan elektrische installaties kunnen werken en deze veilig kunnen