Zoeken in normen
918 resultaten
6.3.102 Interruption
A short interruption, where the work location is not left, is not regarded as an interruption.
6.4.1.5
The work location should be marked out by suitable barriers, ropes, flags, lamps,
signs etc.
Adjacent live switch panels shall be distinguished by additional, clearly visible
means, for example clear warning signs secured to the front of doors.
6.4.2.1
These protective devices shall be selected and installed to provide sufficient protection
against the expected electrical and mechanical stresses.
6.4.2.1.101 The provisions used as screens, barriers, insulating or other covers shall be properly
maintained and stay in place during the work activities.
6.4.2.1.102 When installing such protective devices in the live working zone, this
6.4.2.1.102
When installing such protective devices in the live working zone, this shall be done
according to the procedure for dead working or according to the procedure for live
working.
6.4.4 Construction work and other non-electrical work
[not applicable]
6.101.2
Work activities in other risk-increasing conditions
NOTE See also
annex N.
6.101.2.1 Risk-increasing conditions can be present in installations, premises and environments.
Work activities with risk-increasing conditions shall require extra safety measures
to be taken, depending on the level of the risk, the nature of the work activities,
the use and the condition of the installation
6.101.2.1
Risk-increasing conditions can be present in installations, premises and environments.
Work activities with risk-increasing conditions shall require extra safety measures
to be taken, depending on the level of the risk, the nature of the work activities,
the use and the condition of the installation and the current conditions.
6.101.2.2
If regularly recurring work activities are involved, these extra safety measures shall
be established in writing.
NOTE 1 The other risk-increasing conditions relate to:
a) premises with damp, such as:
1) premises with a bath, shower, swimming pool or sauna;
2) marinas;
3) business premises and sites for agriculture, horticulture and stock farming;
4) cable pits
7 Maintenance procedures
7.1 General
7.1.1 The purpose of maintenance, is to keep the electrical installation in the required
condition.
Maintenance may consist of:
— preventive maintenance:which is carried out on a routine basis with the intention of preventing breakdown
and keeping equipment in good condition;
— corrective maintenance:which is carried out to repair or replace a defective part.
7.1.2
There are two types of maintenance work:
— work where the risk of electric shocks, short-circuit or arcing is present and therefore
the appropriate working procedures (see
Clause 6) have to be applied;
— work where the design of equipment enables certain maintenance (for example replacement
of fuses or light bulbs) to be undertaken safely without full working procedures as
described
Zoeken in de website
52 resultaten
Toelichting n-bepalingen / National Provisions from NEN1010:2015 (english).
Contents
Overview of the National provisions (n-provisions) from NEN 1010:2015
Reasons for the setup of the n-provisions list
Working with non-Dutch Parties
Differences
Examples
Application at Work
Target group for n-provisions
For more information
Overview
NEN 1010 is the most important standard in the field of electrical engineering in
Checklist: executiegevaar
Situatie
Tijdens werkzaamheden is een onder spanning staande kabel met bloot koper in aanraking gekomen met de kabelgoot. Dit heeft geleid tot een onder spanning staande kabelgoot. Een van de werknemers kreeg een elektrische schok van zijn ene naar zijn andere arm.
Risico's
Het risico’s met betrekking tot deze gebeurtenis:
Dit kan leiden tot een hartstilstand, bewusteloosheid, stoppen van
Training voor IV’ers en WV’ers
tekst: Aribert Guiking
foto's: Rob Kaspers
Rob Kaspers geeft trainingen aan installatieverantwoordelijken (IV) en werkverantwoordelijken (WV). Volgens hem zijn deze technici vaak 'bescheiden personen' en zijn ze niet gewend om af en toe stevig te onderhandelen om hun werk optimaal te kunnen doen. Via een tweedaagse training probeert hij dat te veranderen.
Rob Kaspers: “Je moet jezelf zichtbaar
Mag ik de norm uitprinten?
Dat mag, alleen is dit wel voor eigen gebruik.
Moet een NEN 3140-testapparaat zelf ook worden getest volgens NEN 3140?
NEN 3140 is gericht op het voldoen aan de Nederlandse arbowetgeving in het kader van elektrische veiligheid. Dat betekent dat de werkgever op de best mogelijke wijze zeker moet stellen dat het elektrische arbeidsmiddel waarmee hij zijn werknemer laat werken, elektrisch veilig is voor de gebruikelijke werkomstandigheden in de desbetreffende branche.
Een NEN 3140-toetsing zegt niets over de functionaliteit
Mogen wij bij renovatie van bestaande huurwoningen met de onderhoudsdienst van onze woningcorporatie complete keukens plaatsen en nieuw wandtegelwerk en waterleidingen aanbrengen of zijn wij verplicht deze werkzaamheden uit te besteden aan een erkend inst
Nederland kent geen verplichting (zoals wetgeving) om elektrotechnische werkzaamheden (of daarmee verband houdende werkzaamheden) door een elektrisch installatiebedrijf of erkend elektrisch installatiebedrijf te laten uitvoeren. Wel moeten elektrische werkzaamheden waaraan enig risico is verbonden, worden uitgevoerd door ter zake kundige en voldoende opgeleide en/of geïnstrueerde mensen (arbowetgeving
Op welke elektrische apparatuur is NEN 3140 van toepassing?
NEN 3140 is van toepassing op zowel elektrische installaties van gebouwen (en grote machines/industriële installaties) als elektrische arbeidsmiddelen.
Wat zijn de belangrijkste voorschriften uit NEN 3140?
Voor het bedrijfsleven in het algemeen zijn dat de voorschriften voor de periodieke elektrotechnische inspectie van elektrische installaties en de hierop aangesloten elektrische machines en arbeidsmiddelen (elektrische apparaten en gereedschappen).
Voor de specifieke elektrotechnische bedrijven zijn dat de voorschriften hoe zij veilig aan elektrische installaties kunnen werken en deze veilig kunnen