Zoeken in normen
918 resultaten
5.3.3 Inspection
5.3.3.1 The purpose of inspection is to verify that an electrical installation is in accordance
with safety regulations and the specified technical requirements of the relevant standards;
the inspection may include verification of the normal state of that installation.
New electrical installations as well as modifications and extensions of existing installations
shall be inspected prior to
5.3.3.3
Inspections shall be carried out with reference to relevant electrical drawings and
specifications.
5.3.3.3.101 In special cases, the person responsible for an electrical installation may decide
that the inspections can be carried out without drawings and specifications, for example
in simple and clearly arranged installations.
5.3.3.5.102
Inspections shall be carried out using suitable tools, equipment and devices and protective
equipment that prevent hazards, duly considering the hazards of uninsulated live parts.
5.101.6.1
When visually inspecting an installation it is checked whether:
a) the necessary drawings are present and the correct information is indicated;
b) the different (installation) parts are clearly identifiable;
c) any damage present does not cause a hazard;
d) the electrical equipment at least corresponds to the installation requirements;
e) the gangways intended for
5.101.6.2
When inspecting an installation by measuring and testing, it shall be checked that
the requirements have been met as regards:
a) the protective conductors and their connections;
b) the circuit impedances of the electrical system;
c) the earth distribution resistance of earth electrodes;
d) the insulation resistance of each section of the installation;
e) the safe
5.101.6.3
The following criteria shall apply to measurement and testing according to
5.101.6.2:
a) The uninterrupted state of the protective conductors and their connections shall be
measured with:
1) a measurement of the phase-earth circuit impedance or
2) a measurement of all the separate protective conductors with a measurement current
greater than or equal to 0.2 A.
b)
5.101.6.5
The earth distribution resistance of earth electrodes shall be measured using an alternating
voltage.
NOTE If the measurement is not reliable in urban areas, measuring the circuit impedances
will suffice.
5.101.6.8
It shall be established through measuring that the response current and time of earth
leakage circuit breakers do not exceed the values assigned. The proper operation of
the test button may only be checked after the measurements.
5.102.1 General
The electrical installations of extensive, complex and sizeable work equipment shall
be inspected according to
5.101.
Safety functions, such as emergency shutdown switches and collision protection devices
of such extensive, complex and sizeable work equipment shall be checked at least once
a year.
5.102.2
Electrical work equipment shall be inspected with suitable regularity.The time between two successive inspections depends on:
a) the frequency of use;
b) the expertise of the user;
c) the environment;
d) the risk of damage.
NOTE The purpose of regular inspections is to detect any defects that have occurred during
use and that pose a hazard.
Zoeken in de website
52 resultaten
Toelichting n-bepalingen / National Provisions from NEN1010:2015 (english).
Contents
Overview of the National provisions (n-provisions) from NEN 1010:2015
Reasons for the setup of the n-provisions list
Working with non-Dutch Parties
Differences
Examples
Application at Work
Target group for n-provisions
For more information
Overview
NEN 1010 is the most important standard in the field of electrical engineering in
Checklist: executiegevaar
Situatie
Tijdens werkzaamheden is een onder spanning staande kabel met bloot koper in aanraking gekomen met de kabelgoot. Dit heeft geleid tot een onder spanning staande kabelgoot. Een van de werknemers kreeg een elektrische schok van zijn ene naar zijn andere arm.
Risico's
Het risico’s met betrekking tot deze gebeurtenis:
Dit kan leiden tot een hartstilstand, bewusteloosheid, stoppen van
Training voor IV’ers en WV’ers
tekst: Aribert Guiking
foto's: Rob Kaspers
Rob Kaspers geeft trainingen aan installatieverantwoordelijken (IV) en werkverantwoordelijken (WV). Volgens hem zijn deze technici vaak 'bescheiden personen' en zijn ze niet gewend om af en toe stevig te onderhandelen om hun werk optimaal te kunnen doen. Via een tweedaagse training probeert hij dat te veranderen.
Rob Kaspers: “Je moet jezelf zichtbaar
Mag ik de norm uitprinten?
Dat mag, alleen is dit wel voor eigen gebruik.
Moet een NEN 3140-testapparaat zelf ook worden getest volgens NEN 3140?
NEN 3140 is gericht op het voldoen aan de Nederlandse arbowetgeving in het kader van elektrische veiligheid. Dat betekent dat de werkgever op de best mogelijke wijze zeker moet stellen dat het elektrische arbeidsmiddel waarmee hij zijn werknemer laat werken, elektrisch veilig is voor de gebruikelijke werkomstandigheden in de desbetreffende branche.
Een NEN 3140-toetsing zegt niets over de functionaliteit
Mogen wij bij renovatie van bestaande huurwoningen met de onderhoudsdienst van onze woningcorporatie complete keukens plaatsen en nieuw wandtegelwerk en waterleidingen aanbrengen of zijn wij verplicht deze werkzaamheden uit te besteden aan een erkend inst
Nederland kent geen verplichting (zoals wetgeving) om elektrotechnische werkzaamheden (of daarmee verband houdende werkzaamheden) door een elektrisch installatiebedrijf of erkend elektrisch installatiebedrijf te laten uitvoeren. Wel moeten elektrische werkzaamheden waaraan enig risico is verbonden, worden uitgevoerd door ter zake kundige en voldoende opgeleide en/of geïnstrueerde mensen (arbowetgeving
Op welke elektrische apparatuur is NEN 3140 van toepassing?
NEN 3140 is van toepassing op zowel elektrische installaties van gebouwen (en grote machines/industriële installaties) als elektrische arbeidsmiddelen.
Wat zijn de belangrijkste voorschriften uit NEN 3140?
Voor het bedrijfsleven in het algemeen zijn dat de voorschriften voor de periodieke elektrotechnische inspectie van elektrische installaties en de hierop aangesloten elektrische machines en arbeidsmiddelen (elektrische apparaten en gereedschappen).
Voor de specifieke elektrotechnische bedrijven zijn dat de voorschriften hoe zij veilig aan elektrische installaties kunnen werken en deze veilig kunnen